Difference between revisions of "Chrysler Norseman"

From MoparWiki
Jump to: navigation, search
Line 73: Line 73:
 
== Body ==  
 
== Body ==  
  
The car's [[fastback]] roof was made of a special glass by PPG for strength in a rollover. There were 1/4" steel rods in place of the A-Pillars -- which in theory were to break and cause the roof to snap back in the event of a roll over. [[Body panels]] were hand formed aluminum over wooden bucks.  
+
The car's [[fastback]] roof was made of a special glass by PPG for strength in a rollover. There were 1/4" steel rods in place of the A-Pillars -- which in theory were to break and cause the roof to snap back in the event of a roll over. [[Body panels]] were hand formed aluminum over wooden bucks.
 +
 
 +
The team spent 50,000 man-hours and approximately $200,000 to design and build the Norseman. Ghia needed 15 months to construct the one-of-a-kind idea car.
 +
 
 +
Arguably, the most unusual feature of the Norseman to emerge from Chrysler’s design studio was its cantilever roof. The Norseman is nearly unique in this regard since no production car and very few show cars have had this feature. Perhaps the concept would have been adopted for production if the car had not been lost. The lack of A-pillars gave an unobstructed view through the wraparound windshield; the idea had much appeal with Exner. According to his son, Virgil Jr., “He liked to provide good visibility in his cars.”
 +
 
 +
There was more than good visibility involved in the design. Glassmaker, PPG, built the heat-treated structural windshield to make it more crash resistant. Furthermore, the roof was attached in tension to a ¼-inch rod located in place of where the A-pillar posts would normally be present. In theory, such a car in a rollover accident would be provided strong support; the retainers holding the roof and rods together were meant to shear thus releasing the roof from its tension state. Additionally, the roof had a couple of novelty features. One was a brushed aluminum insert and the other was a 12-square foot backlight that could be retracted forward into the roof via an electrical switch. This idea never went into production on any Chrysler product, but a somewhat similar idea – a backlight which retracted into the trunk – was used by Lincoln and Mercury. Fresh air intakes for the passenger compartment were located in the leading edge of the roof, too.
 +
 
 +
Clamshell-type, hidden headlights and a full-width concave grille in combination with a thin bumper located along the horizontal center line and capped at each end with pod-mounted parking lights dominated the front-end view. All of it was finished with a valance panel sweeping underneath the assembly. The front fenders, with their hidden headlights, resembled the nose of a shark.
 +
 
 +
The Norseman’s hood dipped sharply in front, leaving it beneath the frontal portion of the fender line. A light crease beginning at the top of the headlight doors gained prominence as it swept back to the rear of the car and actually formed a horizontal fin along the quarter panel. The fin on the driver’s side ended with the fuel-filler door. This set of fins – as did those atop the quarters – stopped several inches short of the rear of the car.
 +
 
 +
The wheel opening were quite dramatic as well; they were low-cut in both the front and rear and each were scalloped similarly to those of Buick’s limited-production 1954 Skylark.
 +
 
 +
Outside door handles were not employed. Instead, a push-button release not unlike those of the ‘40s Lincoln Continental was used.
 +
 
 +
The rear of the Norseman was no less sensational. Other than its retractable backlight, this show car also featured elliptical nacelles housing chrome-plated bumperettes each with small, round stacked taillights. (A somewhat similar arrangement appeared on the 1957 DeSoto line.) The fastback roof flowed back so far it formed the opening for the center bumper. In profile the Norseman looked something like a rocketship from a contemporary sci-fi movie.
  
 
== Interior ==  
 
== Interior ==  

Revision as of 19:58, 23 September 2017


Chrysler Norseman Dream Car




In 1956, Virgil Exner the head designer of the Chrysler Corporation contracted with Ghia of Turin, Italy to build (at a cost of $150,000) a concept car without an A-Pillar for the 1957 show circuit.

The car was carefully packed into a wooden crate and loaded on the Italian Luxury Liner SS Andrea Doria for shipment to New York. 40 Miles off the coast of Nantucket, the ship collided with the Stockholm. It sank 11 hours later and now rests 235 feet below the surface on its starboard side. Virgil Exner was in the hospital recovering from a heart attack at the time.

The SS Andrea Doria is the "Mt. Everest" of underwater divers -- and many divers have lost their lives diving to it. Only one diver, David Bright, has seen the car (while searching for a lost diver) -- in 1994. He described it as a rusted hulk. Due to the way the ship lies -- he said that he doubts that he or anyone else will ever see the car again. He died in 2006, of cardiac arrest from decompression sickness after a 50th anniversary dive to the ship.

There is a dispute on the colors -- and precious few photos (none in color) exist of the car prior to loading on the Doria. Exner said he ordered the car in Silver paint. Chrysler says that it was to be dark green with green and gray interior. Reporters who saw the car prior to crating, say it was tu-tone blue with red leather and black accents.

Associated Press' coverage of the Norseman was short, simple, and to the point:

The experimental car was built for Chrysler in Turin, Italy, and was being shipped to the United States for public showing. A Chrysler spokesman said Friday the Norseman cost about $150,000, including a year's engineering work. It was insured.



This Wiki is Under Construction, and can use your help!


Please take a moment to add any information you might have on this topic. It is through this type of Member collaboration that the MoparWiki will grow into being the Ultimate Mopar Infobase. The links contained in the Understanding Wikis box in the sidebar can help you get started.


Chrysler Norseman Dream Car
Chrysler Norseman Dream Car
Chrysler Norseman Dream Car

Background

Background of The Exner Era Dream Cars

Quick History of Exner

In 1932, A 23-year-old Virgil Exner was hired by GM's Art and Color Studio. Boss, Harley Earl immediately recognized Exner's design talent. Two years later Enxer was put in charge of the entire Pontiac Studio, a job he kept until 1939 when Raymond Lowry hired him to work on his studio's design contract with Studebaker. Exner worked with Lowry and Studebaker all through WWII, and when the highly advanced 47 Studebaker's were shown to the public in 1946, they were touted as "The First By Far With A Post War Car. It would be the 1949 Model year when the "Big Three" would catch up.

A dispute between Lowry and Exner over credit for the design of the 52 Studebaker caused Exner's firing. Studebaker wasnt impressed with the Lowry proposal for the 52s, and Exner showed them a design he'd been working on at home on his own time. Studebaker liked it and Lowry wanted credit for his employee's work. He was fired when he refused, but Studebaker picked Exner up for their in-house design team. There was little love between Lowry and Exner for the rest of each of their lives.

In 1949, Chrysler President K. T. Keller hired Exner away from Studebaker for the purpose of designing cars that would improve Chrysler's stodgy image. The Chrysler Corporation was well known for its engineering firsts, but not its styling. The Chrysler Corporation's "Small on the Outside - Big on the Inside" designs looked ancient when compared to the 49 Ford and GM offerings. Keller wanted the cars designed to where a man could drive with his hat on. This made the cars appear too tall.

At first Exner worked secretly on Advance Designs, but was soon promoted to head the studio. The model year designs were already locked in through 1954, so Exner began work on the 1955 model, the first year of the "Forward Look" designs.

Keller and Exner agreed that they should step up Chrysler's showing of Dream Cars to compete with Harley Earl's million dollar dream cars displayed in the Motorama shows. They felt this would create excitement with the public on updated designs that would hit the showrooms in the future. However, they would have to do it on a budget no where near the size GM had given Earl.

Exner and Ghia

While working on his first of the Chrysler Dream Cars, the K-310, Exner and his design team were at an impasse. On a previous trip to Italy, K. T Keller commissioned both Pininfarina and Ghia to each build a car of his loose design specs, but allowed them design creativity. The purpose was not to test their design skills, but to test them for quality, fit and finish.

Knowing that the Exner team was having trouble with K-310, Keller invited the team to view the cars that had just arrived from Italy. Pininfarina had closely followed the specs, while Ghia took great liberties with their allowed creativity. Ghia's car was very impressive. The Ghia submission was also far better in quality, fit an finish than the submission from Pininfarina. It was to became the Plymouth XX-500 show car. In addition to Ghia's craftsmanship, their design abilities were a pleasant surprise.

This began the long relationship between Chrysler and Ghia, and more importantly - collaboration between their designers.


Designer

Cliff Voss, William Brownlie under the direction of Virgil Exner

Chassis

Body

The car's fastback roof was made of a special glass by PPG for strength in a rollover. There were 1/4" steel rods in place of the A-Pillars -- which in theory were to break and cause the roof to snap back in the event of a roll over. Body panels were hand formed aluminum over wooden bucks.

The team spent 50,000 man-hours and approximately $200,000 to design and build the Norseman. Ghia needed 15 months to construct the one-of-a-kind idea car.

Arguably, the most unusual feature of the Norseman to emerge from Chrysler’s design studio was its cantilever roof. The Norseman is nearly unique in this regard since no production car and very few show cars have had this feature. Perhaps the concept would have been adopted for production if the car had not been lost. The lack of A-pillars gave an unobstructed view through the wraparound windshield; the idea had much appeal with Exner. According to his son, Virgil Jr., “He liked to provide good visibility in his cars.”

There was more than good visibility involved in the design. Glassmaker, PPG, built the heat-treated structural windshield to make it more crash resistant. Furthermore, the roof was attached in tension to a ¼-inch rod located in place of where the A-pillar posts would normally be present. In theory, such a car in a rollover accident would be provided strong support; the retainers holding the roof and rods together were meant to shear thus releasing the roof from its tension state. Additionally, the roof had a couple of novelty features. One was a brushed aluminum insert and the other was a 12-square foot backlight that could be retracted forward into the roof via an electrical switch. This idea never went into production on any Chrysler product, but a somewhat similar idea – a backlight which retracted into the trunk – was used by Lincoln and Mercury. Fresh air intakes for the passenger compartment were located in the leading edge of the roof, too.

Clamshell-type, hidden headlights and a full-width concave grille in combination with a thin bumper located along the horizontal center line and capped at each end with pod-mounted parking lights dominated the front-end view. All of it was finished with a valance panel sweeping underneath the assembly. The front fenders, with their hidden headlights, resembled the nose of a shark.

The Norseman’s hood dipped sharply in front, leaving it beneath the frontal portion of the fender line. A light crease beginning at the top of the headlight doors gained prominence as it swept back to the rear of the car and actually formed a horizontal fin along the quarter panel. The fin on the driver’s side ended with the fuel-filler door. This set of fins – as did those atop the quarters – stopped several inches short of the rear of the car.

The wheel opening were quite dramatic as well; they were low-cut in both the front and rear and each were scalloped similarly to those of Buick’s limited-production 1954 Skylark.

Outside door handles were not employed. Instead, a push-button release not unlike those of the ‘40s Lincoln Continental was used.

The rear of the Norseman was no less sensational. Other than its retractable backlight, this show car also featured elliptical nacelles housing chrome-plated bumperettes each with small, round stacked taillights. (A somewhat similar arrangement appeared on the 1957 DeSoto line.) The fastback roof flowed back so far it formed the opening for the center bumper. In profile the Norseman looked something like a rocketship from a contemporary sci-fi movie.

Interior

The leather interior of four bucket seats and futuristic gauge pods -- with some type of luminescent paint on the back of the front seats for a lighting experiment.

Drivetrain

Power came from a 331 CI Hemi rated at 235hp, with a 2-speed Powerflite transmission, and shifted by push-buttons.

Car Shows

Movies Appeared in

Magazine Articles

Reference

Internet Links


Random Page | Longest Wikis | Oldest Wikis | Newest Images | Newest Wikis | List of Categories | List of Every Freakin Wiki



Register to Edit
It takes less than 5 minutes to request registration for editing, and we try to approve within 24 hours. Click the Register Link in the Top Bar.
MoparWiki Help
While editing Wikis may at first glance appear a little overwhelming, it really isn't. You will find this site's HELP (link found in the sidebar) to be very strong and easy to understand. The best way to start is with small edits and working on your user page -- and you will become a Pro in no time.